Graphics Display Device Driver for OS/2 Systems Supported: IBM Systems with S3 Trio64V+/64V2 video subsystems. Driver Version: 3.03.14 IMPORTANT: o This package contains an OS/2 graphics-accelerator device driver that supports the Trio64V+ (765), and Trio64V2 DX/GX (775/785) chip sets from S3 Incorporated. o Read this entire document before beginning the device driver installation. The installation procedure in this document must be used to install this device driver. The OS/2 Selective Install procedure can not be used to install this device driver. o The two device driver installation diskettes must contain the volume labels of "S3 DRV1" (without the quotation marks). o Device driver features include: - DDC monitor detection support, - under the OS/2 Warp/Merlin "System - Settings" notebook a user can select the monitor Refresh Rate, - large and small font support for WIN-OS/2 sessions, - WIN-OS/2 support is based on latest S3 Windows 3.1x drivers, - the device driver is enabled for the Configuration Installation Distribution (CID) method, and - a one diskette installation package. CONTENTS ________ 1.0 Supported Features 1.1 Supported Resolutions 1.2 Supported Adapters 1.3 Technical Support 1.4 DDC Monitor Support 1.5 Selecting Large or Small Fonts for Windows 2.0 Preliminary Installation Steps 2.1 Setting OS/2 Warp/Merlin to VGA Mode 2.2 Setting OS/2 2.1x to VGA Mode 2.3 Preparation for CD-ROM or LAN Installation 3.0 Installation from Diskette 4.0 Installation in a CID Environment 5.0 Limitations 6.0 Trademarks 1.0 Supported Features _______________________ This graphics-accelerator device driver provides seamless support for accelerated video graphics and advanced color resolutions when used with the minimum required video memory. It conforms to the OS/2 32-bit, flat memory model and is designed to function as a 32-bit Presentation Manager graphics-display device driver under the OS/2 32-bit graphics engine. This device driver supports setting the refresh rate using the System - Settings notebook (page 2 of the Screen tab) in the OS/2 System Setup folder, and monitor detection using Display Data Channel (DDC) protocols. 1.1 Supported Resolutions *===================================================* * Mode * Resolution * Memory * Trio * * * * Required* Family * * * * *-------------------* * * * * 764/765 * 775/785 * *------*--------------*---------*---------*---------* * 101 * 640x480x8 * 1 MB * Y * Y * *------*--------------*---------*---------*---------* * 103 * 800x600x8 * 1 MB * Y * Y * *------*--------------*---------*---------*---------* * 105 * 1024x768x8 * 1 MB * Y * Y * *------*--------------*---------*---------*---------* * 107 * 1280x1024x8 * 2 MB * Y * Y * *------*--------------*---------*---------*---------* * 111 * 640x480x16 * 1 MB * Y * Y * *------*--------------*---------*---------*---------* * 114 * 800x600x16 * 2 MB * Y * Y * *------*--------------*---------*---------*---------* * 116 * 1024x768x16 * 2 MB * Y * Y * *------*--------------*---------*---------*---------* * 212 * 640x480x24 * 1 MB * N/S * N/S * *------*--------------*---------*---------*---------* * 112 * 640x480x32 * 2 MB * Y * Y * *===================================================* NOTES: o BPP = Bits Per Pixel (color depth); 8 = 256 colors, 16 = 65,536 colors, 24 = 16,777,216 colors & 32 = 16,777,216 colors. o Y = Supported; N/S = Not Supported. o 1 MB only - 640x480x24 is supported for 1 MB memory configuration only; for 2 MB and above, 32 bits per pixel (BPP) is supported. o S3 BIOS supports 1600x1200x8 with 2 MB; S3 OS/2 device driver needs 4 MB of memory. o S3 BIOS supports 800x600x16 with 1 MB; S3 OS/2 device driver needs 2 MB of memory. o S3 BIOS supports 1280x1024x16 with 3 MB; S3 OS/2 device driver needs 4 MB of memory. o S3 BIOS supports 800x600x32 with 2 MB; S3 OS/2 device driver needs 4 MB of memory The 32 bpp device driver might need a large swap space on the hard disk, for example, 15 MB. 1.2 Supported Adapters For a comprehensive list of products that have been tested by IBM and are OS/2 compatible, refer to the "OS/2 Hardware Compatibility List" book. This book is available electronically in the following locations: http://www.austin.ibm.com/pspinfo/os2hw.html IBM National Support Center BBS (data connection: 919-517-0001) CompuServe (IBM OS/2 Support Forum \Library\IBMFiles\PCMTABLE.ZIP) PRODIGY LAN Server & OS/2 BBS - Sydney, Australia IBM Austria BBS - Vienna, Austria IBM BBS - Vancouver, BC, Canada IBM PS BBS - Hong Kong IBM OS/2 BBS & IBM AP OS/2 BBS - Singapore IBM BBS - Belgium IBM BBS - England IBM BBS - Spain OS2BBS - Denmark Hitline BBS- Switzerland DAP & PSP BBS - Italy IBM BBS - Jakarta, Indonesia IBM BBS - Thailand NOTE: The compatibility hardware test information supplied is provided for information purposes. IBM makes no warranty, express or implied, with respect to the operation of OS/2 on the personal computers listed. 1.3 Technical Support Updates for this device driver, when available, may be obtained from the following sources: http://www.pc.ibm.com IBM National Support Center (data connection: 919-517-0001) IBM National Support Center (voice connection: 800-772-2227) 1.4 DDC Monitor Support VESA Display Data Channel (DDC) 1 and 2B protocols are supported, allowing similarly enabled computers and operating system software to identify the monitor and its capabilities. This device driver automatically detects DDC monitor capabilities and sets the monitor to the maximum refresh rate which it supports. If, after installing this device driver, you switch from a non-DDC monitor to a DDC monitor or switch to a different DDC monitor, you must run the DDC Display Setup program in the System Setup folder. Use the following procedures when installing a DDC monitor. 1. Reset the monitor to the lowest refresh rate available. This will prevent the system from setting a refresh rate higher than that supported by the new monitor. 2. Shut down your computer and install the new monitor. 3. Restart your computer. 4. Select the "DDC Display Setup" icon in the OS/2 System Folder. 5. When you are instructed to do so, shut down your system and restart it. 1.5 Selecting Small or Large Fonts for Windows The default font sizes for Windows sessions are listed below. Resolution Default Font Size ---------- --------------------------- 640x480 Small 800x600 Small 1024x768 Large 1280x1024 Large 1600x1200 Large NOTE: Large fonts are not available for the 640x480 resolution. Use the following procedures to select small or large fonts for Windows sessions. 1. Select the "S3 Windows Font Size" object in the OS/2 System Setup Folder. 2. Click on the radio button next to the font size you wish to select. 3. Click on the OK button. 4. A message will display saying that the new settings will take take effect the next time you restart your Windows session. Currently open sessions will not be affected by the new settings. 5. Click on the OK button. 6. Start any WIN-OS/2 window or full-screen session. The setting you select will remain in effect until you explicitly change it, you change your display resolution, or you install a new display driver. 2.0 Preliminary Installation Steps ___________________________________ The following steps must be performed before you install the graphics-accelerator device driver: 1. You must have OS/2 DOS Support installed. 2. If you previously installed SVGA support, you must reset the resolution to VGA mode, using the procedures in the following section. 3. The device driver installation diskette must contain the diskette volume label of "S3 DRV1" (without the quotation marks). The volume label may be applied using the OS/2 LABEL command. 4. After driver installation, the OS/2 SYSLEVEL command can be used to confirm the new driver version level. Following execution of the SYSLEVEL command, look for SYSLEVEL.VID. For example: C:\OS2\INSTALLATION\SYSLEVEL.VID Vision868/968/Trio32/64/64V+/64V2 Version 3.03 Component ID 562107701 Current CSD level: S330312 Prior CSD level: S330312 In this case the current version level is S3 3.03.14. 2.1 Setting OS/2 Warp/Merlin to VGA Mode If you are installing this driver on OS/2 Warp/Merlin , do the following: 1. Turn on your computer. If your computer is already on, press Ctrl+Alt+Del to restart it. 2. When a small white box appears in the upper-left corner of your screen, press Alt+F1. 3. When the Recovery Choices screen appears, press V for Warp Version 3 or press F3 for Warp Version 4(Merlin). Your video subsystem is now restored to work in VGA mode. If you want to install a new video adapter refer to Chapter 16 "Video Procedures," in the User's Guide to OS/2 Warp/Merlin. 2.2 Setting OS/2 2.1x to VGA Mode If you are installing this driver on OS/2 2.1, 2.11 or OS/2 for Windows, and you installed from diskettes, do the following: NOTE: If your monitor has lost synchronization, start OS/2 using the OS/2 Installation Diskette. When prompted insert diskette 1, press F3 to display a command prompt, and then use the following instructions to reset your display mode. 1. Under OS/2 2.1, before running RSPDSPI, delete the following file: *OS2 DRIVE*:\OS2\INSTALL\00S3.DSC 2. Under OS/2 2.11, before running RSPDSPI, delete the following file: *OS2 DRIVE*:\OS2\INSTALL\00S3.DSC 3. Be sure RSPDSPI.EXE is in the \OS2\INSTALL directory. If it is go to step 6. If it is not, insert Diskette 8 into into drive A and unpack RSPDSPI.EXE with the following command: C:\OS2\UNPACK A:\INSTAID C: /N:RSPDSPI.EXE where A: is the drive containing Diskette 8, and C: is the drive where OS/2 is installed. 4. Type C: and then press Enter. 5. Type CD C:\OS2\INSTALL and then press Enter. 6. Type the following: RSPDSPI /PK:VGA /SK:NONE /S:A:\ /T:C: In /T:C:, C: is the target drive where OS/2 is installed. In /S:A:, A: is the source diskette drive for installing the device driver. Then press Enter. 7. In some cases you will get screen instructions telling you to "Insert the diskette with the following label into drive A: Display Driver Diskette 1. Then press Enter". Please follow these instructions. 8. Perform a shutdown and restart your computer. 2.3 Preparation for a CD-ROM or LAN Installation If you are installing this device driver on OS/2 2.1, 2.11 or OS/2 for Windows, and you installed from CD-ROM or a LAN, do the following: 1. Under OS/2 2.1, before running RSPDSPI, delete the following file: *OS2 DRIVE*:\OS2\INSTALL\00S3.DSC 2. Under OS/2 2.11, before running RSPDSPI, delete the following file: *OS2 DRIVE*:\OS2\INSTALL\00S3.DSC 3. Be sure RSPDSPI.EXE is in the \OS2\INSTALL directory. If it is go to step 6. If it is not, unpack RSPDSPI.EXE with the following command: C:\OS2\UNPACK E:\DISK_8\INSTAID C: /N:RSPDSPI.EXE where C: is the drive where OS/2 is installed, and E: is the CD-ROM or LAN drive. 4. Type C: and then press Enter. 5. Type CD C:\OS2\INSTALL and then press Enter. 6. Type the following: RSPDSPI /PK:VGA /SK:NONE /S:E:\OS2SE21\ /T:C: In /T:C:, C: is the target drive where OS/2 is installed. In /S:E:, E: is the source CD-ROM or LAN drive. Then press Enter. 7. Perform a shutdown and restart your computer. 3.0 Installing from Diskette _______________________________ To install the graphics-accelerated device driver from diskette, do the following: 1. If system is not in VGA mode, select VGA mode. 2. Insert the driver installation diskette into drive A (or any other diskette drive). In the following sequence the A drive is assumed. 3. Open an OS/2 full-screen or OS/2 window session. 4. At the OS/2 command prompt, type the following command to copy all necessary files to the OS/2 drive: A:SETUP where A: is the diskette drive which contains the device driver installation diskette. Then press Enter. Due to the limitations with a single pass installation. A dialog box may come up during installation with the message, "The installed adapter does not support the selected display driver. Do you wish to continue?". Please continue the installation by selecting the Yes button. 5. When the Monitor Configuration/Selection Utility window appears, the "Install Using Defaults for Monitor Type" choice is preselected. Select OK. Do not select "Install Using Display Adapter Utility Program" since this method of setting refresh rates is not supported anymore. NOTE: DSPINSTL determines the hardware configuration by creating the \OS2\SVGADATA.PMI file. If the \OS2\SVGADATA.PMI file has not been created, the adapter will not be supported. This process can take several seconds and will black-out the screen. 6. When the Source Directory pop-up window appears, insert the prompted graphics-accelerator driver diskettes into drive A. At this point the source directory must specify the drive containing the installation diskette (e.g. A:). If necessary change the source directory, then select Install. 7. When the installation is complete, shut down your system, remove the diskette, and restart your computer. 8. When the system has restarted: a. Open the OS/2 System folder. b. Open the System Setup folder. c. Open the System object. d. When the Settings notebook appears, select the Screen tab. If your monitor has been detected as Plug and-Play (DDC) compatible, go to step 10. 9. On Screen page 2, select your display from the display list. If your display does not appear in the list, select Default. It might be necessary to restart your computer to have all refresh rate options available. 10. When the system has restarted: a. Open the System object and select Screen page 1, as in step 8. b. Select a screen resolution and a screen refresh rate. c. Close the Settings notebook. d. Perform a shutdown and restart your computer. NOTES: o If the selected vertical refresh rate is not supported by your monitor, delete \OS2\VIDEO.CFG file and reboot. This will set the refresh rate to the default value. A new refresh rate can now be selected using the procedure described above. o During the installation of this driver, DISPLAY.LOG and DSPINSTL.LOG files are created in the OS/2\INSTALL directory. These files identify the OS/2 system files that were updated and indicate whether the installation was successful. The contents of these files might be useful if you need to report an installation problem. o If the video memory size is changed after the device driver is installed, the device driver must be reinstalled in order for the system to recognize the change. Not reinstalling the driver might result in serious system problems. o When starting a Windows session from a DOS command line, use the WINOS2 command rather than the WIN command. Additionally, you must modify the C:\AUTOEXEC.BAT file. Place the following line anywhere after the "@ECHO.OFF" line in the AUTOEXEC.BAT: COPY C:\WINDOWS\WINOS2.COM C:\WINDOWS\WIN.COM 4.0 Installing in a CID Environment ____________________________________ NOTES: o The server must contain a directory named S3_DRVS on the same drive where the OS/2 diskettes reside. The S3_DRVS directory must contain all of the files from the graphics-accelerator device driver installation diskette. o OS/2 must have been successfully installed on the client using the CID (Configuration Installation Distribution) method. To install the graphics-accelerator device driver using CID, use the following information to modify your LCU command file. NOTE: The following information is meant as a guide. Your LCU command file might be different. /*****************************************************/ /* LCU PRODUCT DATA SECTION */ /*****************************************************/ . . . x.s3video = 15 x.15.name='S3 Video' x.15.statevar = 'CAS_' ** x.15.name x.15.instprog = 'x:\img\s3_drvs\SETUP.CMD', ' x:\img\s3_drvs ' ** bootdrive ** ' CID' x.15.rspdir = '' x.15.default = '' /*---------------------------------------------------*/ /* NUMBER OF PROGRAMS SET UP IN THE */ /* PRODUCT DATA SECTION */ /*---------------------------------------------------*/ NUM_INSTALL_PROGS = 15 /*****************************************************/ /* INSTALLATION SECTION */ /*****************************************************/ . . . when OVERALL_STATE = 2 then do if RunInstall(x.s3video) == BAD_RC then exit Call RebootAndGotoState(3) end when OVERALL_STATE = 3 then do if RunInstall(x.s3dspinstl) == BAD_RC then exit Call CheckBoot end . . . /******************************************************/ /* ROUTINE SECTION */ /* The following information should already exist in */ /* the LCU command file. */ /******************************************************/ . . . RebootAndGotoState: parse arg new_state, other /* Set the state to go to in OVERALL_STATE */ rc2 = SetState(new_state, 'RebootAndGotoState', 1) Call SaveStates /* Save the environment vars */ Call Reboot /* Reboot the machine */ return . . . /*****************************************************/ END OF LCU INFORMATION TO BE ADDED /*****************************************************/ Following is an explanation of the line that is executed in the LCU command file: C:\OS2\INSTALL\DSPINSTL /pd:c:\os2\install\00S3.DSC /S:X:\img\s3_drvs /T:C: /res:640x480x256 /u /pd:c:\os2\install\00S3.DSC is the dsc laid down during setup phase. /S:X:\img\s3_drvs where X:\img\s3_drvs is the redirected source path. /T:C: where C: is the drive where OS/2 is installed. /res:640x480x256 is a resolution/color depth from the list of "Supported Resolutions" that appears earlier in this README. In this example 256 colors is specified. Enter "64K" to specify 65,536 colors or "16M" to specify 16,777,216 colors. /u means Unattended installation. NOTES: o After a CID installation the end user should go to section 3.0 "Installing from Diskette" and continue with step 8. o Be sure you have the stated video memory required, as listed in "Supported Resolutions" earlier in this README. A safe choice is 640x480x256. Any of the listed resolutions can be selected, but your display might be damaged if you select a resolution that your display does not support. o To select a refresh rate, SVGA.EXE can be executed again separately after DSPINSTL. Example, SVGA ON INIT 1024 75 This will create another \OS2\VIDEO.CFG file with 75Hz as the default at 1024x768 resolution. The prior \OS2\VIDEO.CFG file should be deleted first. o After the graphics-accelerator device driver has been successfully installed on the client machine using the CID method and the client machine is restarted, the resolution will be as specified by command line argument. 5.0 Liminations _______________ 1. CID install pauses due to SVGA.EXE loading in the background. Work around: In the CID install script, do not initiate any other processes until DISPINSTL completes execution. Ensure that no other processes are running during CID install. This can be accomplished by adding the following line to the CONFIGSYSLINE keyword of the CID response file: SET RESTARTOBJECTS=STARTUPFOLDERSONLY 2. DISPINSTL does not allow CID selection of monitor and refresh rate. WORK AROUND: Requirements: * A system with the same graphics subsystem and monitor configured with this graphics-accelerator device driver, the correct display type, the desired resolution and refresh rate. Step 1: Copy Configured Video/Display Data Files * copy the video and display data files containing information about the display type, resolution and refresh rate to the CID server (\img\svgadata). > copy \os2\svgadata.pmi x:\img\svgadata > copy \os2\video.cfg x:\img\svgadata Step 2: Create CID Command File * create a command file to copy svgadata.pmi and video.cfg to the client system's \OS2 directory via CID. * reboot the client system. * the client system will be configured with the correct driver, display type, resolution and refresh rate. Another work around is to delete \OS2\VIDEO.CFG and to execute SVGA.EXE again after DSPINSTL completes. Example: SVGA ON INIT 1024 75 to set 75Hz as the default refresh rate at 1024x768. 3. In all modes, video corruption or out-of-sync screen is displayed when using Alt+Esc to switch between WIN-OS/2, OS/2, DOS window and DOS full-screen sessions started from the Startup folder. To avoid this situation, do not start sessions from the Startup folder or press Alt+Esc several times to restore. 4. Some programs, such as WINBENCH95, WINBENCH96, and After Dark 3.0. were written specifically for the Windows environment. In the Windows environment, these programs prevent any keystrokes from interfering with their proper execution. However, in the OS/2 environment, it is possible to switch context away from the Windows session without notifying these programs. General Protection Faults (GPSs) may result. Therefore, context switching during the execution of WINBINCH95 and WINBENCH96 tests is not recommended. Also, context switching during the execution of the After Dark 3.0 demo is not recommended. 6.0 Trademarks ______________ The following terms are trademarks of the IBM Corporation in the United States and/or other countries: Aptiva IBM OS/2 WIN-OS/2 The following terms are trademarks of other companies: TRADEMARK OWNER After Dark Berkely Systems, Inc. CorelDRAW Corel Corporation Lotus Lotus Development Corporation Micrografx Micrografx Incorporated S3 S3 Incorporated Trio64/Trio64V+ S3 Incorporated Trio64V2 S3 Incorporated Ventura Publisher Ventura Software, Inc. Vision 864/868/964 S3 Incorporated Windows Microsoft Corporation WordPerfect WordPerfect Corporation 1-2-3 Lotus Development Corporation IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY RELATED PATENTS OR COPYRIGHTS. THIS DRIVER IS COPYRIGHTED BY INTERNATIONAL BUSINESS MACHINES CORPORATION. ALL APPROPRIATE RESTRICTIONS APPLY. (End of Document)