CD-3314 (140-0538) Operation Faxback Doc. # 7200 USING THE RADIO WARNING: To protect your hearing, set VOLUME to its lowest setting before you turn on the radio. 1. Set FUNCTION to RADIO. The PWR/BATT (Operation/Battery) indicator lights and the radio turns on. 2. Set BAND to FM or AM 3. Set BEAT/MONO/STEREO by using these guidelines. To listen to FM stereo, set it to either of the two STEREO positions. The FM STEREO indicator lights when you receive an FM station in stereo. To listen to FM monaural, set it to MONO. 4. Adjust TUNING to the desired station. NOTES: For the best AM reception, rotate the CD-3314 to position the built-in AM antenna. For the best FM reception, fully extend the telescoping antenna and swivel it to the position that produces the best reception. If FM stereo reception get noisy while BEAT/MONO/STEREO is set to STEREO, set it to MONO. The sounds is no longer in stereo, but reception improves. 5. Adjust VOLUME and TONE to the desired levels. 6. To turn off the radio, set FUNCTION to TAPE (RADIO OFF). The PWR/BATT indicator turns off. USING THE CD PLAYER CAUTIONS: A sudden shock or jolt while a CD is playing might suddenly change the speed of the CD's rotation or cause the CD player to skip the track it is playing and, as a result, momentarily mute or distort the sound. This is not a malfunction. If you move the CD-3314 from a very cold room to a warmer one, moisture can condense on the pickup lens, preventing proper disc pay. If this happens, turn the CD player off then wait 30 minutes before attempting to operate it again. LOADING/UNLOADING A CD 1. Set FUNCTION to CD. CD DISPLAY shows 00 for about 2 to 3 seconds and the PWR/BATT indicator lights. 2. Press OPEN-CLOSE to open the CD compartment. 3. Place a CD in the compartment with the label facing up. 4. Press OPEN-CLOSE to close the compartment door. CD DISPLAY shows 00 for about 5 seconds and the CD momentarily spins. When the CD stops spinning CD DISPLAY shows the total number of tracks. 5. To remove the CD, press (OPEN-CLOSE Selection), grasp the CD by its edges, and carefully pull it out. CAUTIONS: To prevent possible damage to the CD or the CD player, always remove a loaded CD. Only when it is stopped. Before you move the CD-3314. PLAYING A CD WARNING: The CD player has a wide dynamic range. Do not turn the volume too high during a program's soft sections or its sudden loud sections might cause hearing discomfort. To protect your hearing, set VOLUME to the lowest setting before you turn on your CD-3314. 1. Press >II. The CD player begins playing the first track and CD DISPLAY shows the current track number. NOTE: To temporarily pause the CD, press > II. PAUSE and the track number appear on the display and the CD stops playing. Press >II again to resume play. 2. Adjust VOLUME and TONE to the desired levels. 3. To stop play before it automatically stops at the end of the last track, press (stop button). REPEAT PLAY You can repeat a single track or all the tracks on a CD or in a programmed sequence (see "Programmed Play"). To repeat a single track, before or during play, press REPEAT until repeat one appears on the display. To repeat the entire disc or a programmed sequence, before or during play, repeatedly press REPEAT until Repeat all appears on the display. To stop repeat play, press REPEAT until repeat all or repeat one disappears from the display. AUDIBLE SEARCH To search forward on the CD, press and hold down >> during play. As you hold down >>, the CD rapidly advances and you hear the music or information at a faster speed. Release >> to resume normal play For reverse search, press and hold down << during play. Release << to resume normal play. SKIP SEARCH You can skip tracks in either direction on a CD or in a programmed sequence (see "Programmed Play"). During play, press and release >>I to skip to the beginning of the next track. During play, press and release I<< to skip to the beginning of the current track. Repeatedly press >>I or I<< to skip forward or backward through additional tracks. NOTE: Pressing >>I while the last track is playing has no effect. CUING You can cue a track before you begin normal or programmed play or during pause. To cue a desired track, press >>I or I<< until the desired track number appears on the display. Then press >>I to play the track. PROGRAMMED PLAY Storing a Programmed Sequence You can program up to 21 tracks on a CD to play in any sequence. 1. Press MEMORY while the player is stopped. OO appears on the display. 2. Repeatedly press >>I or I<< until the desired track number appears on the display. 3. Press MEMORY again to store the displayed track. OO reappears on the display. NOTE: The memory location number does not appear on the display. 4. Repeat Steps 2 and 3 to store up to 21 tracks. CAUTION: When all 21 memory locations are used, the first programmed track reappears on the display. When this happens, any additional track you enter replaces the displayed track. NOTE: You can store a track more than once. Reviewing a Programmed Sequence To review a programmed sequence, while the CD is stopped, repeatedly press MEMORY. The display shows the programmed CD track numbers in sequence. Playing a Programmed Sequence 1. Press >II. As each programmed track plays, MEMORY and the track number appear on the display. 2. To temporarily pause the CD, press >II. The CD stops playing and PAUSE, MEMORY, and the track number appear on the display. Press >II again to resume play. 3. To stop play before it automatically stops at the end of the last track, press (stop button). NOTE: If the memory has not been cleared, you can replay a program even if the CD player is stopped and MEMORY does not appear on the display. Simply press MEMORY. When the display shows the first programmed track number, press >II. Replacing Tracks in a Programmed Sequence 1. While the CD is stopped, repeatedly press MEMORY until the track number you want to replace appears on the display. 2. Press >>I until the new track number appears on the display. 3. Press MEMORY again to store the displayed track in place of the previous track. Clearing a Programmed Sequence Any of the following actions clears a programmed sequence. Press OPEN-CLOSE to open the CD compartment door after the CD stops turning. Set FUNCTION to TAPE (RADIO OFF) or RADIO. Disconnect the power source. CD CARE TIPS Even thought a compact disc is very durable, treat its surface with care. Always handle a CD by the edges to avoid fingerprints and always keep it in its protective case or sleeve when it is not in use. Do not write on either side of the CD, particularly the non-label side. (signals are read from the non-label side.) Do not store CDs in high-temperature, high-humidity locations. The CDs might warp. Fingerprints and scratches on the CDs surface can prevent the laser beam from correctly reading the digital information. To clean the CDs surface, use a CD Cleaner Kit (such as Cat. No. 42-116). Keep CDs dry. A drop of moisture can act as a lens and affect the laser beam's focus. Remove moisture with a soft, dry cloth. Move the cloth in straight lines, starting from the center and moving out toward the outer edge. Do not move the cloth in circles. Be sure the CDs are fully dry before you use them. USING THE CASSETTE PLAYER PLAYING A CASSETTE TAPE 1. Set FUNCTION to TAPE (RADIO OFF). 2. Press STOP/EJECT to open the cassette compartment door. NOTE: To prevent the tape from getting tangled in the record/playback mechanism, before you insert the cassette, take up any slack in the tape by turning the cassette's hub. Avoiding touching the tape. 3. Insert a cassette tape with the side you want to play facing you, the exposed tape edge down, and the full reel to the left. Then close the compartment door. 4. To play the tape, press PLAY. The PWR/BATT indicator lights. NOTE: To rapidly move the tape forward or backward, before or during play, press F.FWD or REWIND. 5. Adjust VOLUME and TONE to the desired sound levels. 6. Press STOP/EJECT to stop the tape before it automatically stops when it reaches the end. The PWR/BATT indicator turns off. NOTE: To temporarily pause play, press PAUSE. Press PAUSE again to resume play. RECORDING A CASSETTE TAPE You can record from the CD player or radio. CAUTION: You cannot press down RECORD when you load a cassette with the erase-protection tab removed. Do not force down RECORD or you might damage the recording mechanism (see "Preventing Accidental Erasure"). NOTES: The CD-3314's Automatic Level Control (ALC) automatically adjusts the recording level. VOLUME has no effect on recording. Be sure the erase-protection tabs are in place on the cassette tape you are using to record. We recommend regular length (60-or 90-minute) cassette tapes. We do not recommend long-play cassette tapes such as C-120s because they are very thin and can easily tangle in the recording or playback mechanism. Tape quality affects the quality of the recording. For low-noise, wide-range recordings, we recommend you use normal bias tape. Most CDs and pre-recorded tapes contain copyrighted material. Copying or dubbing of copyrighted materials is a violation of federal copyright laws and could result in fines and/or imprisonment. RECORDING FROM THE CD PLAYER 1. Set FUNCTION to CD. NOTE: Before you load a cassette tape, turn the cassette's hub to move the tape past its leader. 2. Insert a blank cassette tape or one you want to record over into the cassette compartment. 3. Load a CD into the CD player (see "Loading/Unloading a CD"). 4. Press PAUSE then RECORD on the cassette tape deck. RECORD and PLAY lock down. 5. Press >II twice on the CD player. The CD DISPLAY shows the first track number. 6. Press PAUSE on the cassette tape deck then >II on the CD player. The cassette deck starts recording and the CD begins playing. The CD DISPLAY shows the current track number. NOTE: To temporarily pause the recording, press PAUSE on the cassette deck. Press PAUSE again to resume recording. 7. To stop recording, press STOP/EJECT on the cassette deck. 8. To stop the CD player before it automatically stops when it reaches the end, press (stop button). RECORDING FROM THE RADIO 1. Follow Steps 1 through 4 under "Using the Radio." 2. Insert a blank cassette tape or one you want to record over into the cassette compartment. 3. Press RECORD on the cassette tape deck. RECORD and PLAY lock down. The cassette deck starts recording from the radio. NOTES: To reduce or eliminate a whistling sound sometimes produced when recording from AM broadcasts, set BEAT/MONO/STEREO to any of the three positions that give you the best sound quality. To temporarily pause the recording, press PAUSE on the cassette deck. Press PAUSE again to resume recording. 4. To stop recording before the tape automatically stops when it reaches the end, press STOP/EJECT on the cassette deck. 5. To turn off the radio, set FUNCTION to TAPE (RADIO OFF). TAPE CARE TIPS Restoring Tape Tension and Sound Quality After you play a cassette tape several times, the tape might become tightly wound on the reels. This can cause playback sound quality to deteriorate. To restore the sound quality, fast-forward the tape from the beginning to the end of one side, then completely rewind it. Then loosen the tape reels by gently tapping each side of the cassette's outer shell on a flat surface. NOTE: Be careful not to damage the cassette when tapping it. Do not touch the exposed tape or allow any sharp objects near the cassette. PREVENTING ACCIDENTAL ERASURE Cassette tape have two erase-protection tabs - one for each side. To protect a recording from being accidentally recorded over or erased, use a screwdriver to remove one or both of the cassette tape's erase-protection tabs. WARNING: Removing the erase-protection tabs does not prevent a bulk eraser from erasing a cassette. NOTE: If you want to record on a tape side after you have removed the erase-protection tab, place a piece of strong plastic tape over the side's erase-protection hole. Be sure you cover only the hole originally covered by the erase-protection tab. ERASING A CASSETTE TAPE If you no longer want a recording, you can record over it or erase it. To erase a previously recorded section of a tape, simply record over it. To erase the entire cassette tape, let the tape record silence to the end. You can quickly erase both sides of a cassette tape using a bulk eraser (such as Cat. No. 44-232, not supplied) available at your local Radio Shack store. (CJD/all-07/19/94)